video corpo
Add to favorites

#Industry News

Fiber Laser Cutting Machine Solutions For Ten Rare Problems

fiber laser cutting machine, fiber pipe cutting machine, tube laser cutting machine, metal cutting machine, furniture laser cutting machine

Today, we Golden Laser summarize the solutions to the ten rare problems of laser cutting machines.

First, press the control panel on the machine to light out the button, the laser tube does not shine?

1. Press the Set button on the machine panel → Is the laser power zero? Can't be zero;

2. Press the Set button on the machine panel → Is the laser mode manual? The default is automatic mode;

3. Please check if the positive and negative electrodes on the laser tube are loose or not connected properly;

4, directly press the test button on the laser power supply to see if it can emit light, such as light, laser power, laser tube is good, if there is no light, please exchange power;

5. If the power supply is still not working, please replace the motherboard.

Second, the laser mouth does not emit light? Spot mode is not round, moon switch, toothed?

1. First open the lid, press the light button to see if the laser tube does not emit light, such as light, that is, the light path is corrected;

2. When dimming the road, the spot pattern on the transparent tape is not round, the shape of the moon is toothy, please clean the mirror and the focusing mirror. If not

3. Check if the mirror and the focusing mirror have spent or lost the film. If there is an internal situation, replace the above accessories;

3. When the laser cutting machine is working halfway, the panel display shows “Out of limit data error” and the machine stops working.

1. The machine and the computer must have good grounding;

2, open the cutting software → click the "File" menu → communication settings to change the receiving and sending buffer time to 5 or 10;

3. Replace the data cable or motherboard.

4. Press the same direction button on the panel. The motor will rotate forward and reverse and the motor will not be locked.

1. Check if the drive is red and the motor drive is interchangeable.

2. Replace the motor cable in the chain. If not

3. Replace the motherboard.

5. Is the laser tube high pressure head water leaking and sparking?

1. Disconnect all power first, and wipe the high pressure head with cotton cloth. Gently scrub

2. Cut off the broken water pipe and reconnect it to the laser tube. Then bundle with a cable tie;

3. Reconnect the high voltage line. There are 7 silver wires in the high voltage line, one cannot be less;

4. Dry the wetted area of ​​the high pressure head with a fan. After half an hour, turn it on again.

Sixth, power on alarm?

1. Whether the water pipe is turned on;

2. Check if there is water in the water tank;

3. Check if the water tank water pipe is caught or there is something to press the water pipe so that the water pipe does not circulate;

4. Check if the water tank signal line is loose with the machine or the signal line itself has a problem;

5. If it is a water tank alarm, check the water tank;

6, if it is the motherboard alarm, first confirm whether the motherboard water protection terminal is beating, if you jump to replace the motherboard.

Seven, boot does not return to the original point?

1. Is the XY pulse indicator of the motherboard bright?

2. Replace the motherboard.

Eight, laser cutting machine is not round?

1. Check if the screws on the XY screw seat are tightened;

2. Check if the board is clamped;

3. Check if there is an error in the graphic;

Nine, dimming road

1. First, the laser power is adjusted to about 10%, and then the laser is turned off and then dimmed;

2, the first light adjustment: first use a transparent tape attached to the reflector to shoot, to confirm whether the light is in the middle of the mirror, then adjust the three rotating screws on the mirror to adjust, the light hits the center of the lens barrel, and finally Install the laser nozzle and then shoot it, whether it is at the center of the laser nozzle;

3. Correct the laser vertical: first adjust the laser power to about 40%, and use the organic board to confirm whether the upper and lower lights are vertical. If it is vertical, the light is turned on;

4. If the laser tube is tilted up and down on the organic board, the left and right obliquely adjust the laser tube bracket to swing left and right;

5. Opposite light: After confirming the focal length of the upper and lower laser heads, loosen the screws on the right and front of the upper laser head to adjust;

6, cut the field with a wooden board, the width of the knife slit, the verticality of the board.

10. Is the list in the laser software anonymous or undetectable? Normal all numbers

1. Click on the refresh list to see if it can be detected.

2. Check if the COM terminal of the computer connection data cable is loose;

3. Replace a computer to check it;

4. Replace the motherboard.

Fiber Laser Sheet Metal Cutting Machine

Details

  • Jing He San Lu, Dongxihu Qu, Wuhan Shi, Hubei Sheng, China
  • Golden Laser

    Keywords