MANIBO company News and Trends items

Gripping is made by a series of vacuum pads, fixed on a stainless steel tubular frame, with vacuum generation by compressed air (Venturi system). The vacuum pads are manufactured in silicone rubber certified FDA. The manipulator is equipped with a pneumatic tilting device, limited to about 45°, to facilitate the gripping operation from the supplying chain. The tiltin...

Gripping is made by a proper shaped vacuum pad, with gasket suitable for gripping also on surfaces covered with plastic film. Also in case of feeding air pressure fall down, an air tank allows to maintain the feeding to the vacuum generator and maintaining the part gripped, while the safety system brings it slowly to the ground. The equipment can be supplied in executi...

Gripping is made by two self centring, properly shaped jaws, undercut the external edge of the box. To facilitate the gripping in the correct position the jaws are provided with a centring device. Because of the necessity to use the equipment in food environment, it is completely manufactured in stainless steel, then all the surfaces are completely polished, to avoid ...

Gripping is made by eight vacuum pads disposed on two parallel rows of four pads each one. The two vacuum pads rows can oscillate free, to have the possibility to adapt to the different diameters of the rolls. The rolls can turn to the vertical position to grip the cardboard boxes where, inside, the rolls are located. Vacuum is made by compressed air, Venturi system. A...

Gripping is made by four vacuum pads: two on the upper edge and two in the registration plate side of the door. The vacuum pads frame can tilt free, to have the possibility to orientate the back door and to make all the operations foreseen for the assembling phases. Vacuum is made by compressed air, Venturi system. Also in case of feeding air pressure fall down, a va...

Gripping is made on the front by two centring pins and with two jaws outside the body of the casting part. The jaws are properly shaped and orientated to adapt themselves to the geometry of the part to handle. The gripping tool is equipped with a manually rotation, operated by a wheel, with the possibility to lock the position with steps of 90°, to allow the operator ...

Gripping is made on the external part of the hub by properly shaped jaws covered with protecting rubber. The gripping tool can rotate manually, with the possibility to lock the position with steps of 90°, to facilitate the operator during the assembling of the hub and to orientate it during the preliminary preparation operations. A double control handle has been foresee...

Gripping is made by three vacuum pads, with the possibility to regulate the position, with pneumatic vacuum generation. It is possible to regulate the position of the vacuum pads to allow the gripping of all the dimensions of blades always corresponding to their center of gravity, having the possibility to tilt easily the blades. The manipulator is equipped with a 90° ...

Gripping is made from the external in proper points where, the jaws, properly shaped, allow the gripping and the centring of the part, to facilitate the following operations. The gripping tool is equipped with rotating device, operated by a pneumatic motoreducer, to tilt 90° the turbo compressors. The position of the control handle can be vertically adjusted in order ...

Gripping is foreseen on the external side by two jaws, each one with a double pin, coated with protection rubber. A safety device keeps the gripping of the lifted part also in case of feeding air pressure fall down. Because of the big range of dimensions to grip, it has been foreseen a gripping tool with a proper closing and opening stroke. Then to avoid to lose time...

Gripping is made by a vacuum pad on the vertical side of the body of the condenser. To allow the gripping corresponding on the vertical lifting axis, the vacuum pads assembly is fixed on a “C” shaped support, to recover the overhanging due to the gripping position. Vacuum is made by compressed air, Venturi system. Also in case of feeding air pressure fall down, a safet...

Gripping is made on the external diameter, by two self centring jaws, each one with two rods covered of rubber, to avoid the damaging of the pipe. The handling attachment is equipment with a pneumatic tilting device to orientate the rolls from horizontal to vertical and vice versa. The control handle can slide vertically, in balanced mode, to allow to grip and to rele...

Gripping is made on the internal diameter, by jaws covered of rubber, to avoid the damaging of the thread. The handling attachment has been designed to grip of all the dimensions of bushings, without the necessity to regulate or change the jaws. To avoid to interfere with the cases or with the next bushings, both during the gripping than during the releasing, long jaws h...