The magnum XP is ideally suited for pumping high volumes of heavy slurry that are abrasive, corrosive, or just plain tough to pump.The magnum XP 8X6X18, 12X10X23, and 14X12X22 can deliver flow rates up to 7500 gpm and head pressures up to 540 feet. The compact overall dimensions of the magump XP make it an excellent choice for high volume mobile and stationary applicati...
Design features:Take a small bulk ,high efficiency. Special froth impeller with large inlet size, this benefit to the large size solids come There is difference between pumping froth slurry and normal slurry.SBF slurry pump of high performance to pump high viscosity slurry. The problem of handling froth in some process circults can be very frustrating. Froth often will a...
Model:SSA 4×3×13 Discharge capacity:60~80 m 3 /h Pump Head: 22~28 m Efficiency:65% Motor power:11/15 kW Motor speed:1450 / 1750 rpm Inlet diameter:4″ Outlet diameter:3″ The series centrifugal sand pump has these features: (1) open impeller,apply to transport high viscosity drilling liquid. (2) combination seal for a long service life. (3) use universal bearing houses and...
There are three kinds of material for your convenience, SS316, CD4M and CN7M, to meet different working condition request. Both of the two types of pumps run outstanding hydraulic performance, supreme reliability, lowest cost and very easy maintenance.
River Sand Suction Machine Diesel Engine Coupling SG Gravel Pump SG series Gravel Pump Sand Pump Introduction: 1. Gravel Sand pump (dredge pump) is designed as single casing connected by means of clamp bands and wide wet-passage. 2. The wearing parts are made of ultra chromium abrasion-resistance alloys, long service life and very low failure rate. 3. The pumps are desi...
The HS series pumps are designed for the continuous pumping of highly abrasive, high density slurries with minimal maintenance requirements, the horizontal centrifugal pumps will maintain high efficiencies over the wear life of its components. The rubber and metal lined pumps feature casings which are radially split into two halves. Minimum casing bolts reduce maintenanc...
The SXP type frac pump is single-stage, single suction centrifugal slurry sand pump, which is used on frac truck mostly. The Mission Magnum XP centrifugal pump is good at handling big capacity of high abrasive, corrosive and plain tough slurries. The Mud pump wet parts are made of high chrome alloy, hardness HRC58-62. The impeller is open type and back vane design decrea...
Magnum SM series mud centrifugal pumps are mainly design for solids control circulating system of oilfield drill rig. It can be used to provide drilling liquid with a certain discharge capacity and pressure to sand, desilter and mud mixer, to assure these equipments work efficiently. Features: 1. Open impeller design, ideally dealing high viscosity drilling slurries. 2....
ZNA Series Sunbo ZNA filter press feed pump suits for various occasions such as coal dressing, environmental protection, aluminum plant, steel plant, smelting, etc. The special hydraulic design insures the pump performance curve is steeper than common slurry pump, from big flow & small pressure to small flow & high head. In the early process of feeding, the valve is no...
Sand Pump & Gravel Slurry Pump SG Series Introduction: SG series is single casing horizontal slurry pump and also named as gravel pump, sand pump and dredging pump, which is designed specifically for continuous pumping of extremely aggressive slurries, with a wide particle size distribution. Capable of handling large particles at consistently high efficiency results in...
SSA series centrifugal sand pump is designed for continuous operation of heavy slurries that are abrasive, corrosive, or just plain tough to pump. SSA Series Pump are more compact in design, and it can be adaptted for hydraulic motor drive. It is mainly used for oilfield frac trucks as well as blending and pump dealing for water well drilling solid control system applica...
SBF Slurry pump is horizontal froth slurry pump is pumping slurry with obstinate froth. of a special design-inducer blade impeller to solve this problem easily. Design features: Take a small bulk ,high efficiency. Special froth impeller with large inlet size, this benefit to the large size solids come There is difference between pumping froth slurry and normal slurry....
The pumps are mainly design for solids control circulating system of oilfield drill rig. It can be used to provide drilling liquid with a certain discharge capacity and pressure to sand, desilter and mud mixer, to assure these equipments work efficiently. Features: 1. Open impeller design, ideally dealing high viscosity drilling slurries. 2. Combination seal for a l...
The pumps are designed for the continuous pumping of highly abrasive, high density slurries with minimal maintenance requirements, the horizontal centrifugal pumps will maintain high efficiencies over the wear life of its components. The rubber and metal lined pumps feature casings which are radially split into two halves. Minimum casing bolts reduce maintenance and min...
HS(R) pump is horizontal centrifugal heavy duty slurry pump and it is designed for the continuous pumping of high abrasive, high density slurries with minimal maintenance requirements. It will maintain high efficiency over the wear life of its components. The rubber and metal lined pumps feature casings which are radially split into two halves. Minimum casing bolts reduc...
The mud centrifugal pumps are mainly design for solids control circulating system of oilfield drill rig. It can be used to provide drilling liquid with a certain discharge capacity and pressure to sand, desilter and mud mixer, to assure these equipments work efficiently.
The 14x12x22 frac pump is using advanced manufacturing technologies and material sciences to extend the long service life. It is single stage, single suction, horizontal centrifugal slurry sand pump, which is suited for handling big capacity of abrasive, corrosive and plain tough slurries with high sand concentration, especially oil and gas stimulation and hydraulic frac...
Specification: Capacity (m³/h): 324-3600 Head (m): 26-70 Speed (r/min): 300-500 Max. Efficiency η%: 72 NPSH (m): 3-6 Allowable Max. Power (Kw): 1200 Description: The range of Dredge and Gravel pumps is designed specifically for continuous pumping of extremely aggressive slurries, with a wide particle size distribution. Capable of handling large pa...
The HS series pumps are designed for the continuous pumping of highly abrasive, high density slurries with minimal maintenance requirements, the horizontal centrifugal pumps will maintain high efficiencies over the wear life of its components. The rubber and metal lined pumps feature casings which are radially split into two halves. Minimum casing bolts reduce maintenan...
HS(R) series slurry pump is widely used in metallurgy, mining, mineral processing, dredging, de-watering, water treatment, coal washing, mill, cyclone feed, tailing, power, building material...etc. various industrial sites. HS pumps are called different names for different working duties: Mineral processing pump, Mill discharge slurry Pump, Booster pump, Feeding pump, Ta...
1. Usage and Application Range SSA series centrifugal sand pump includes virtually all of the features of the SM series pumps. SSA series pumps are more compact in design and can be adapted for hydraulic motor drive.These features make .SSA series pump ideal for use in applications such as oilfield frac trucks as well as blending and pump charging for water well drillin...
Features: 1. Open impeller design, ideally dealing high viscosity drilling slurries. 2. Combination seal for a long service life. 3. All pump models, use same frame support, convenient in maintenance and cut down costs. 4. The major parts are made from anti-wear nodular iron,and long service life.
WN type Dredging Pump is horizontal, single-stage cantilevered structure, which is designed to meet the requirement of the contractor demanding and comprehensive dredging requirement. WN type dredge pump impeller passage is very wide, to continuous pumping gravel or high plastic clay and not happens jam. The minimal amount of wear parts design in these dredge pumps resul...
Features: ◆ Wear resistant metal or rubber wet end parts, long service life ◆ Wide options for impeller ◆ Various types of pump seals to suit different working condition ◆ Discharge branch can be positioned at intervals of 45 degree ◆ Can be installed in multistage series Specifications: ◆ Size: 25 mm to 450 mm ◆ Capacity: up to 5000 m3/hr ◆ Maximum Heads: u...
SV(R) series of pumps are popular with many clients with special installation requirements and widely applied in pool and pit. Its wear-resistant metal liner could handle abrasive slurries with rough particles and high concentration. Specifications: ◆ Outlet: 40-300mm ◆ Capacity: to 1548 m³/h ◆ Head: to 40 m ◆ Type: Centrifugal, Vertical, Single Casing ...
