The CDW-802XT low-temperature impact testing instrument is a compressor refrigeration equipment newly developed by our company according to the requirements of JB5376-91 "Technical Conditions for Low Temperature Bath" and GB/T 229-2007 "Charpy Notch Impact Test Method for Metal Materials". The equipment achieve automatic uniform cooling and constant temperature of the sa...
This machine is specially designed to test the impact resistance of helmets and to conduct penetration resistance tests.
This testing machine is mainly used for the test of pressive strength of duct finished products.
XJL-300B-type drop hammer impact testing machine for plastic, glass, ceramics and other non-metallic materials samples or pipe to do impact test, is a test instrument used to evaluate the impact resistance of materials
The XJL-600A drop hammer impact tester is suitable for impact test of steering rod products in the automotive industry. It is a test instrument for evaluating the impact resistance of product components.
This machine is mainly used for the detection of torsion spring and elastic component torque.
This machine is used to test the mechanical properties of finished products of road bridge rubber bearings.
The LGM-225 wet sand rubber wheel wear tester is a wet sand semi-free abrasive wear tester. The test machine meets the requirements of the ASTM G105 wet sand rubber wheel abrasion test method standard.
According to the requirements of GB/T50081, the mechanical properties of the concrete after hardening can be divided into concrete compressive strength, tensile strength, flexural strength, static compressive modulus and surface hardness, etc. Typical testing machine equipment suitable for this standard: As a well-known large-scale testing machine factory in Jinan, Ji...
Sponge special test to meet the tensile and compression test of non-metallic materials; and tensile strength, tear strength, elongation measurement function of cotton test piece
The LPW-80A Cemented carbide tooth drop hammer fatigue impact testing machine is used to evaluate the simulated use conditions of such products, and to test the durability and safety of the products.
It is mainly used for the reciprocating compression test of foam polymer materials, and measuring the residual deformation rate, so as to know the material's dynamic fatigue characteristics.
The rubber low-temperature brittleness tester is determined the highest temperature when the sample is damaged by the impact of the vulcanized rubber under the specified conditions, that is, the brittleness temperature, and the performance of the non-hard plastic and other elastic materials under low temperature conditions can be comparatively identified. It can measure ...
LGM-130 type dry sand rubber wheel abrasion tester is the dry sand semi free abrasive material abrasion tester. The principle of the machine is that it uses the rubber wheel rotating clockwise to drive the abrasive materials such as quartz sand (mine sand, sand, sand) to wear on various metal or non-metal materials, so as to test the wear resistance of the material.
The notch test tests the resistance of PE pipes to slow crack growth. The notch milling machine produces V-shaped notches in polyolefin pipes in accordance with ISO 13479. The notched pipes are then subjected to a pressure test.
The test machine used to test the GB/T28289-2012 its mandatory test items "thermal profile of the high temperature endurance load test." It can be done six series of samples at the same time, according to the sample size of 10-25pcs per string range, the maximum load 6KN.
The test machine specifically for motorcycles and mopeds light alloy wheel radial drop hammer impact test.
This machine is mainly used for the gauge marks (also used for non-metal materials) of the plate specimens referred to in the GB/T 228 standard.
It is used to test the elevator in the test range of the wire rope and the rope for the aircraft control in the range of 12.7-15.88 (1.6mm-9.5mm).
This machine is designed by industry or national standards CJ/T3012-1993 "cast iron inspection manhole cover", CJ/T121-2000 "recycled resin composite inspection manhole cover" and JC889-2001 "steel fiber concrete inspection manhole cover", GB/T 23858-2009 "inspection manhole cover", etc.for testing the bearing capacity of the manhole cover.
The equipment adopts the compressor refrigeration technology, and uses the principle of heat balance and the stirring circulation mode to achieve automatic uniform cooling and constant temperature of the sample, which can fully meet the various temperature control indexes stipulated by the national standard GB8363-07.
MCD-6 Pad friction coefficient testing machine is mainly used for testing wire rope and pad friction coefficient.
It is suitable for bending test of metal bars and construction rebars to determine the ability of metal materials to resist bending deformation.
This machine is mainly used for the compression strength test of brick, stone, cement, concrete, etc, also it can be used for other material’s compressive performance test after equip special fixture.
Cupping testing machine is used to evaluate the resistance of metal materials to the anti-cracking or anti-separation of metal substrates after being subjected to the indentation test under the standard test method; Two-way composite cylinder for measuring metal stretchability.
The NDW-2000 computer control clutch and brake torsion testing machine is specially used for the static load of electromagnetic clutch, dry and wet brake, analog clutch and brake working state
GYB-2000 computer controlled electro-hydraulic servo steel pipe compression testing machine is specially used for the compressive strength test of steel pipe flattening test. Fully meet the ISO 8492:2013 Metallic materials -- Tube -- Flattening test.
The Liangong Group were invited to participate in the 15th International Exhibition of Testing and Measuring Equipment Testing & Control Exhibition on October 23-25, 2018 at Moscow, Russia. The company showcase the overall solutions of our testing machine products in the field of physical measurement to exhibitors and visitors from all over the world, and conduct compre...
Computer control electro-hydraulic servo single space tensile testing machine adopts single space cylinder up-setting structure. The two-way differential cylinder is used to realize the two-way test of tension and compression in one space, which is suitable for the occasion of tensile test.
The equipment adopts imported compressor refrigeration technology, adopts the principle of heat balance and circulating mixing method to achieve automatic uniform cooling and constant temperature of the sample.
This machine adopt the oil cylinder down-setting type, is mainly used for metal, nonmetal tensile, compression, bending and shear test. Test operation and data processing in accordance with GB/T 228-2010 "metallic materials tensile testing" requirement, if change the structure and related parts replacement and can meet the ASTM, ISO and other international standards requ...
This testing machine is suitable for the ball stud shaft impact bending test in the global industry standard for the automotive industry. The machine is novel in structure and consists of a frame part, a lifting system, a hammer body, a single row ball stud mounting support, a safety protection system and a control system. The machine can adjust the impact energy by adju...
The device is mainly used to determine the stainless steel pipe, carbon steel, steel-related standard test, the sample fracture. It characterizes the presence of small cracks in the steel under dynamic loading yield stress brittle fracture. Test method is to lift a certain quality of the hammer to a certain height, and then release by the static, the hammer free fall imp...
The high temperature chamber for impact test shall comply with the provisions of GB/T 229 and other relevant national standards regarding the impact test temperature.