TIGER 402 CNC HR 4.0 + CB 6001: THE RIGHT SOLUTION FOR: HIGH PRODUCTION, PRECISION AND WORK FLEXIBILITY TO CUT ALLUMINIUM AND LIGHT ALLOYS!

TIGER 402 CNC HR 4.0, segatrice a disco HM, automatica elettropneumatica a discesa verticale, con funzionamento anche in ciclo semiautomatico, per il taglio di alluminio e leghe leggere, da 45° destra a 60° sinistra.

OPTIONAL VERSION: TIGER 402 CNC HR 4.0 RB , with automatic rotating table 3 positions: 45°left, 0° and 45°right.

– CNC machine with controlled double axis multimicroprocessor so as to obtain, on the same bar or on the material located on the loading magazine CB6001 (OPTIONAL), up to 300 cutting programs each of different lengths and quantities.

– CB 6001, for high production, for round, square and rectangular bars up to the maximum cutting dimensions indicated on the brochure. The CB6001 must be ordered together with the machine.

– TIGER 402 is completely covered to give safety to the operator (during working cycles, access to cutting area is hindered by a timed opening system) and for sound insulation.

A FEW FEATURES:

– 8” touch screen display operator interface and push buttons for all functions of the sawing machine. It is simple and intuitive with a self-learning feature, it guarantees a reliable use and it controls all cutting parameters in real time.

– Panel with low tension controls: polyester membrane keypad with tactile thermo-shaped buttons which give out an acoustic signal when pressed.

– The headstroke, according to the dimensions of the material which has to be cut, is set directly from the control panel.

– Sawing head movement on double linear guide with preloaded slides with recirculating ballscrews.

– The headstroke, according to the dimensions of the material which has to be cut, is set directly from the control panel.

– Head down stroke by means of pneumatic cylinder with coaxial hydraulic brake to obtain the maximum cutting rigidity.

– Shearing stress control.

– Transmission system with serrated pulleys and belts.

– Blade rotation with 2-speed motor at 1400/2800 rpm.

– Automatic device to lubricate the blade only when the machine is cutting.

– Rotation pin with thrust bearing to grant rotation precision and stability.

– Bar feeder has a length of 1000 mm and consists in a system given by screw/nut with recirculating ballscrews with stepper motor and vice with sideways movement so as to feed in also deformed bars.

– Chip conveyor predisposed to mount optional chip collector.

– Pneumatic double locking vice.

– Pneumatic vertical vice.

– Indicator with flashing light in case cycle is stopped.

– Control and function system protected against in-going and/or out-going electrical and electromechanical phenomenon.

– Machine arranged for handling with movement equipment.

– Circular blade Ø 400 mm.

– Service keys and instructions manual for maintenance and spare parts list.

CB 6001 BAR CHUTE LOADING MAGAZINE 6000 MM FOR MEP SAWING MACHINE MODEL TIGER 372 CNC LR 4.0 and TIGER 402 CNC HR 4.0.

CB 6001 – Since this unit has a maximum load of 2400 kg (8 bars of round solid with a diameter of 80 mm) we recommend to fix it to the floor so as to avoid even minimum unalignments.

A FEW FEATURES:

– This accessory allows you to cut in sequence all the bars which are positioned onto the chute of the loading magazine and consequently the machine can work, even for a long time, without the presence of the operator.

– The CB 6001 has a 80-cm bed where the inclination can be regulated. It can be loaded till it is full with round, square and rectangular solids or sections up to the maximum dimensions indicated in the feature table.

– When a restpiece which cannot be cut remains in the machine, the loading magazine sends forward a new bar pushing out the restpiece. The new bar is positioned for the face cut which isn’t counted on the cuts made.

– The CB 6001 has a sturdy tubular steel structure which is partially demountable for ease in transport.

– The transmission mechanisms (gears and racks), as well as the system to feed in bars individually, are made out of steel.

– The CB 6001 can be ordered together with the sawing machine or afterwards, on condition that the machine has been ordered together with the accessory “equipped to mount CB 6001 w/vice to reduce restpiece”.

– The CB 6001 requires a 6 BAR air supply and the motor is powered by the controller of the sawing machine itself.

– Cutting materials which have a certain wall thickness generate also a lot of chips; for this reason, we recommend to equip the sawing machine with a motorized chip evacuator.