Ceramic Piston Plunger Fits General Pump and Interpump. The Ceramic Plungers are mostly made of alumina (Al2O3) or zirconia (ZrO2) ceramics which have superior wear resistance, corrosion resistance, high-temperature resistance and impact resistance properties etc. When using ceramic plungers instead of tungsten carbide you get longer life on HP-seals and the plunger itse...
The Cordis flow controller utilizes an extremely fast-reacting mems technology sensor upstream from a proportional valve, with the option of a DR-2 regulator for accurate and precise pressure control in a small package. Unlike other mass flow controllers that require a 30 minute warm-up time, large differential pressures, and limited flow ranges, the Cordis requires less...
SPU 5/32 union straight stainless steel push to connect fitting connects two 5/32 tubing with same diameter in the same direction. Stainless steel push in fitting union connector is made of 316 stainless steel for corrosion resistance, FKM seal for chemical-resistance. The durable stainless steel construction makes these fittings ideal for harsh environments that demand ...
ROTAN® delivers the most advanced internal gear design available today, and is dedicated to continued improvement of our already proven pump design. From our oversized ports for higher viscosity products, to our true back-pull-out modular design, ROTAN® pumps deliver quality while reducing down time. Simplified Asphalt Roofing Process Pumps used for: - Unload...
The terminal houses four Liquefied Natural Gas (LNG) storage tanks, each capable of storing up to 52.8 million gallons, a 45,000 tonne Liquefied Petroleum Gas (LPG) tank and a regasification plant. Rotork has been providing actuators at the terminal since it was first constructed, with over 100 electric and pneumatic actuators installed during the initial front end en...
SPE 5/32 union tee stainless steel push to connect fitting connects two 5/32" tube connections in straight line and one branch at a right angle from the middle of the tee with same diameter. The body of 5/32" O.D tubing stainless steel push in fitting is made of 316 stainless steel for corrosion resistance, FKM seal for chemical-resistance. Union tee stainless steel pneu...
The push-pull designed and produced by Longhe Intelligent is widely used in the handling and stacking operations of non-palletized goods. Unlike forklift handling equipment, which usually requires the use of wood, steel, plastic and other styles to carry pallets, the push-pull can use the paper or plastic slip sheet under the cargo to pull the goods to the push-pull. Aft...
SPM 3/8 bulkhead connector stainless steel push to connect fitting connects two 3/8" tube connections on both ends through a panel. Bulkhead connections are used when there is a need to move 3/8" tube through some obstacle. Simply drill a hole, push one part of bulkhead through it, and then screw second part onto the other side. The body of 3/8" O.D tubing stainless stee...
With the “DeviceConfig” software you can set the parameters for the 8049 positioner (Ex, 2-/4-conductor) and the 2030 and 2032 motor actuators from Schubert & Salzer in just a few simple steps and then obtain valuable diagnostic data for optimization of the process. To make setting and changing the parameters for the valve characteristics easy, DeviceConfig contains ...
Clippard new high pressure EHV series valves are precision-built 2-way control valves that accept low voltage, low current signals and convert them to high pressure (500 psig/34 bar) pneumatic outputs. EHV series valves consume very little power and provide exceptionally long life. In addition, they are small in size, quiet, and produce very little heat. These feature...
Boasting more than 68 years of experience in the design, manufacture, distribution and support of adhesive dispensing systems for the tissue, pulp, and paper industries, Valco Melton has first-hand knowledge of the most common concerns of core-winders when investing in their glue supply system. Contrary to the general feeling, the output pressures generated by the more e...
It is made up of supporters on both two ends and several V-shape Polyurethane sealing ring. It is mainly used as hydraulic cylinder seal of hydrostatic testing machine. As it is designed by using multiple sealing rings with high strength supporters on both two ends. It has better sealing effect and longer use-life. According with several standards about hydraulic testin...
The gas-liquid rotary joint is used specially transmitting gas and liquid media, mainly including compressed air, hydrogen, nitrogen, water, oil, coolant and so on.Rotary joints adopt different sealing methods according to different transmission media, mainly including gap sealing, mechanical sealing and sealing of sealing parts. Each type of sealing for rotating joint h...
SPCF 1/4-04 female connector stainless steel push to connect fitting connects a male R, PT, BSPT 1/2 thread to a 1/4" tubing in the same direction. The body of 1/4" O.D tubing to R, PT, BSPT 1/2 female connector stainless steel push in fitting is made of 316 stainless steel for corrosion resistance, FKM seal for chemical-resistance. External tightening with a flat wrench...
SPOC 5/16-04 internal hexagon male connector stainless steel push to connect fitting connects a female R, PT, BSPT 1/2 thread to a 5/16" tubing in the same direction. The body of 5/16" O.D tubing to R, PT, BSPT 1/2 internal hexagon male connector stainless steel push in fitting is made of 316 stainless steel for corrosion resistance, FKM seal for chemical-resistance. The...
Yes…. Hello world… Our first product is out! 24/09/2020 Global Control Engineering exists for more than 15 years, but through this period its main subjective was providing consultancy for several companies. The nature of this work concentrated in highly complex product development and projects. When decision is made to start developing of our own, it was clear that...
A lot has happened to our modular kit system MULTILINE ADAPTIVE + E, a multiple connector for compressed air, vacuum, gases, cooling water, liquids, electrics and electronics. In addition to our version with union nut, our lever version is now also included. Furthermore, now you will also find our standardized M12 round connectors as well as two versions of the M12 po...
ValSize, the proven, easy to use program for the fluid-dynamic design of control valves provides support when determining the required valve flow coefficients (Kv values) for the process data and fluid properties of a given application. Furthermore, it also provides values for the flow velocities in the piping before and after the valve, a calculation of the expected noi...
The sealing component is made up of a polyurethane sealing ring and fan-shaped supporters. It is mainly used in the pressure test of steel pipe by hydro-static testing machine. In the non-working state between the sealing ring and surface of steel pipe exists gap. When hydraulic liquid is applied to the external of the sealing ring, the ring is pressed to enclose the sur...
SPC 1/4-G02 male straight stainless steel push to connect fitting connects a female BSPP, G 1/4 thread to a 1/4" tubing in the same direction. The body of 1/4" O.D tubing to BSPP, G 1/4 male straight stainless steel push in fitting is made of 316 stainless steel for corrosion resistance, FKM seal and o-ring for chemical-resistance. External tightening with a flat spanner...
HIGH QUALITY AT LOW PRICE IN STOCK! CMM 600 l/h (oil pumping, oil heating, oil degassing) at SPECIAL PRICE: - compact (weight -250 kg, L/W/H - 740/520/1350 mm) - simple in operation and maintenance - silent during operation - equipped with sensors - input power - nur 14 kW For technical characteristics and prices contact me directly: +49 421 365 83 216
316L stainless steel push in fitting male connector is made of 316L stainless steel material. Accommodate Metric Tubing O.D: 4mm, 5mm, 6mm, 7mm, 8mm, 9mm, 10mm, 12mm, 14mm, 15mm, 16mm Accommodate Inch (Imperial) Tubing O.D: 1/8", 5/32", 3/16", 1/4", 5/16", 3/8", 1/2" Available Thread Size: BSPT1/8, BSPT1/4, BSPT3/8, BSPT1/2.
EXAIR’s Air Atomizing Spray Nozzles atomize fluids (most commonly water) in a range of spray patterns for a variety of uses. They combine liquid and compressed air to create a mist of atomized liquid that can be easily adjusted to meet the needs of your application. All models use stainless steel construction for durability and corrosion resistance. Air atomizing spray n...
Suitable for almost all shut-off and control tasks, ball sector valves have proven themselves particularly in applications with contaminated, abrasive and viscous media. Due to their special properties, they are used, for example, in the paper, steel, chemical, food and wastewater industries. They are characterized by their high rangeability and high flow capacity. Thank...
TPS Technitube Röhrenwerke GmbH holds a wide range of OCTG, Tubes and Pipes and accessories on stock. With our SPEED PROGRAM we are able to satisfy almost all of your demands within 24 hours with materials EX STOCK!
316L stainless steel male connector accommodates metric tubing O.D ranging from 4 mm to 16 mm and inch (imperial) tubing O.D from 1/8" to 1/2". Thread sizes ranges are from 1/8 to 1/2. The thread types are PT, R, BSPT thread; BSP, G, BSPP thread and NPT thread. 316L stainless steel products certified FDA Compliance Certerficate.
Pneuflex stainless steel banjo (stainless steel pneumatic fitting) material can be 316SS. Ring type banjo fitting. Suitable for banjo bolts (hollow core screws) M10x1.0. 45.5mm and 65.15mm length, 2mm diameter flow nipple, suit for less than 3.5mm I.D hose. Electrolytic Polishing, it’s much brighter than chrome plated and zinc plated. Used on many cars, motorcycle, and ...
Stainless steel transition fittings are designed to connect soft tube on one end and metal tube on other end; one side is stainless steel push in fitting configuration, another side is stainless steel compression tube fitting configuration. Stainless steel transition fittings are used for air, pneumatic, food & beverage, chemical, medical & pharmaceutical systems. They a...
Brass compression fitting male stud elbow consists of three pieces of construction nut, ferrule and body, connects tubing to threaded pipe at a 90 degree angle. Single ferrule compression fittings have fewer possible leak paths than two ferrule fittings. This brass compression fitting is made of nickel plated brass for corrosion resistance, ductility at high temperatures...
Push to Connect Fittings Pneuflex manufacturing has rich experience of over 15 years on designing and producing pneumatic push to connect fittings to satisfy various industrial requirements. Pneuflex's push to connect fittings provide a convenient and easy method of connecting and disconnecting tubes without the use of tools. Push to connect fittings become absolutely e...
Pneuflex brand inner hexagon plug can be BSPT thread, NPT thread, BSP thread and metrice thread.
Pneuflex offers two style M5 thread flow control valves: flow control-out valve (meter-out speed controller) and flow control-in valves (meter-in speed controller). Flow control-out valves adjust the speed of air flow from thread to tubing. Flow control-in valves adjust the speed of air flow from tubing to thread. The tubings size can be 4mm and 6mm.
Stainless steel compression tube fitting male elbow is made of stainless steel 316, and is a mechanism used both to seal and to grip tubing. This stainless steel compression tube fittings consist of four parts: body, a front ferrule, a back ferrule and nut. The mechanical advantage and geometry of this kind of fitting produces a leaktight assembly in high-pressure, high-...
1/16 NPT Thread Male Connector Pneumatic Fitting from China manufacturer Pneuflex, the thread is 1/16 NPT, and the tube size can be 4mm, 6mm, 5/32 inch and 1/4 inch.
Pneuflex brand 316 stainless steel pneumatic push in fittings - male elbow swivel from China. BSPT thread, NPT thread and BSP thread can be selected. Features of Pneuflex's 316 Stainless Steel Push in Fittings All Pneuflex's stainless steel push in fittings are made from forged 316 stainless steel or machined bar stock. The thread of Elbow, Tee and Brach fittings co...
316 stainless steel joint fittings are an alternative and very reliable way to connect pneumatic hose. Accommodate metric tubing O.D ranging from 4mm to 12mm and accommodate inch tubing O.D ranging from 1/8" to 1/2". Thread sizes ranges from1/8 to 1/2, the type of thread can be BSPT thread, NPT thread, BSP thread and metric thread.
