The patented fine-grained steel guarantees highest static and dynamic strength with the smallest bolt diameter! The fastening bolts of modern boltable lifting Points have to withstand extreme daily loads – in any direction. This hardest forces on bending loads has safely to be accepted in terms of statics and dynamics – even under lowest temperatures and maximum heat...
DEREK IS HERE: HALL 10; B 32. DEREK INDEXABLE MILLING CUTTERS (SKS SERIES) FOR HIGH FEED MACHINING Features: ● Taper-off design minimizes interference; ● Double clamp structure promises a high rigidity; ● Excellent for high-feed machining; ● Special insert with three cutting edges increase cost performance; ● Inserts: WDMW050316; WDMW06T320; WDMW0805...
An additional pivotable control panel has been adapted to the pallet changer setup station. The user interface – easy and intuitive to operate with drag and drop – makes day-to-day production tasks easier. As with other previous Hermle development projects, they will first be tested in our internal machining manufacturing under production conditions until they are ready ...
In today’s highly demanding industries such as Nuclear, Shipbuilding or Aerospace, the welded assemblies must be perfect. To achieve a perfect weld, the best welding machine has to be accompanied by the best end preparation machine. Conscious of the high standards of our customers, PROTEM delivers premium tube machining solutions. Machining quality is repetitive and...
The new spindles are characterised by a vastly improved dynamic stiffness. Thanks to the hydroviscous system, damping of natural vibrations is enhanced considerably. In the axial direction, it was possible to achieve an improvement in dynamic stiffness, for example, of up to 135 %. This results in significantly reduced natural vibrations in the machining process, enablin...
The compact dimensions are the result of a design that was optimised both for low power consumption and heat radiation. Powerful processors with high computing speed and an intelligent layout with potential for expansion ensure a high preservation of value. The PLC is programmed according to IEC 61131-3 and the newly designed development environment provides new tools fo...
More clamping Torque • Universal, with or without coolant through the collets. • From 16 mm. till 50 mm. direct clamping. • Nut diameter starting at 40 mm. for 16 mm. chuck. Starter KIT composition • 1 High Power Torque Chuck. • 5, 6, or 8 collets depending the chuck diameter. • 1 Chuck case. • 1 Key for the collet. • 1 Key for the nut.
1.Particularly suitable for aluminium, light alloy, PVC and stainless steel profiles Machine equipped with CNC control unit c/w 10" color monitor and touch screen system 2. Three controlled axis 3.working area 5000*300*200mm 4.TAIWAN SYNTEC control system 5.Japan YASKAWA servo motors and drivers 6.Taiwan YYC rack gear and pinion 7.Taiwan LIMING reduc...
You've come to the right place! The Breton ShapeMill is a machining centre with 5 interpolated axes specifically designed for workshops producing pieces made from natural and engineered stone. It is ideal for restauration work.
The US25 portable pipe bevelling tool is the most powerful, robust, reliable and versatile portable tube and pipe bevelling/ facing machine in the world. A wide capacity: For diameters ranging from 12.5mm ID – 120mm OD 0.5’’ ID - 4.7’’ OD Versatile cutting head accepting up to 4 cutting bits: Four machining operations can be carried out simultaneously or ...
The new Head has an extremely versatile composition which includes 18 vertical spindles (7 on the Y-axis and 12 on the X-axis) + 4 horizontal spindles (2 on the Y-axis and 2 on the X-axis). The oval (instead of round) cylinders guarantee a high boring force, up to 460N, for optimum precision during panel machining. High machining speed: the horizontal spindles re...
Resource-saving innovation in lighting by Waldmann is now even more efficient LUMATRIS opens up for the LED technology the field of medium- and large-sized machines or systems. The innovative Light Forming technology converts the dot-shaped light characteristic of LEDs into a homogenous area light. The Eco mode which is part of the standard scope of delivery provide...
1: grinded gears made of induction hardened case-hardening steel - sprindle bearings (Super Precision) with preload. High load capacity, rigidity and rotation accuracy 2: variety of feeding movements and threading 3: digital indication for movements and speed (rpm) 4: frequency variable speed control with a permannet cutting speed and a high spinning moment 5: monoli...
- High efficiency - High repeatability at all connector faces by automatic pressurisation by controllable water connection - Easy handling by menu-driven microprocessor controlling up to 45 polishing programs can be stored - Polishing of 3 to 36 connectors per fixture is possible - 3 point fixation of polishing fixture - Maintenance-free - T...
Stacking of 10 profiles (max. 6,5 m length). Manual barcode labeling system integrated with single-lines. Servo controlled automatic swing of the saw to all angles between 30° and 150° with 0.1° accuracy. Drain slot routing, drilling and routing at variable angles. Automatic screwing of reinforcement steels. Drilling of fixation, triple handle and hin...
The latest Grinder presented is the model PV2400 suitable for balls up to 2400 mm OD (64”). This machine has a big covering structure in stainless steel to protect operators and to contains the working fluids. Main features of this machine are: - the rigid structure, - the using of roller guideways to assure the best accuracy and the best finishing surface of the wo...
For angle settings, F-Tool offers a compact, economic, stainless square block-index-table which is very well suited for sporadic use. The universal index adapter plate can be turned around its centre using the 90° grid index and in addition the index pin can be adjusted within a 15° graticule. By omitting the index pin, the adapter plate can be adjusted variably on a ver...
ECOROLL''s multiple roller deep rolling tool HFK02 exp. (expanding) is specially designed to deep roll two large radii on main bearings and crank pin bearings on crankshafts in the same process. Deep rolling results in a considerable increase in fatigue strength, i.e. in the amount of load alternations possible without the work piece suffering fatigue or fracture. Deep r...
The new clamping jaws offer even more flexibility thanks to the "plus more grip" teething. The "plus more grip" clamping jaws have properties that are ideally suitable for the production of blank to finished parts. Non-ferrous metals, plastic, aluminium and steel can be very quickly and tightly clamped in the grip area to only 3 mm in height for five-sided optional machi...
The driver bits can be easily replaced by holding the main unit with one hand while turning the sleeve with the other hand.
Features: ● Adapter standard: BT MAS403; ● Clamping diameter: 16mm, 20mm, 25mm, 32mm, 40mm; ● With optional sleeve: CSO32, CSO40; ● Oil feed. Application: ● This BT-SLO series oil-feed tool holder is for cutting tools with weldon shank or plain shank used on those machines without internal coolant supply.
The extraordinary robust design, linked with a high stiffness, precise linear guides (ball rail systems) on the gantry bridge and a heavy duty runway, based on milled railway profiles S 49, guarantee the very best quality and a long duration of life. Excellent and powerful digitally controlled AC-drive systems with high precision planetary gears as well as selected rack...
-80 000 RPM -Precision unit for drilling, deburring etc -Highly stable bearing system -Low noise level (67 dB(A)) -HFS 100: also available as high speed grinder (HFS100), which includes a hose -suitable for manual handling of the unit Power 80 [W] Speed (idle) 80.000 [rpm] Torque* 0.02 [Nm] Min CCSS** 54 [mm] Run-Out*** <0.007 [mm]
It is the first time that burrs will be available under the Dormer product brand, with a comprehensive assortment of designs and shapes to choose from, including ball nosed cylinder, pointed tree, oval, flame, 60° and 90° countersinks, cones and inverted cones varieties. The introduction of the burrs is part of a wider product launch by Dormer Pramet on 1 April 2015 –...
Protective bellows are generally not expensive but if mounting new ones requires the machine to be dismantled in whole or in part, they can be costly to replace. Dynatect-Halltech offers the ideal solution in the form of protective bellows made to customer specifications and provided a zip fastener (or a hook and loop fastener). Depending on space conditions, a zip is ...
Cubic concept entails that the machine frame on which the axis drives are fitted is no longer part of the machine but part of the drive itself. It allows eliminating the need to design and integrate high-precision fixation extensions to the main machine frame. It greatly simplifies the design, saves many hours of stiffness simulation on sophisticated 3D CAD software, and...
Its lightness (less than 25 kg) as well as its small dimensions (a size of 15 cm) allow the Serco to be easily carried on site to perform machining works in the narrowest spaces. The SERCO XP 600 can be directly clamped on the flange but it is also possible to use a chain if there is no available clamping possibility. The Serco XP600 is mainly designed for the onsite o...
It comes fully equipped and ready to use and is suitable for lapping components from 50 mm diameter up to 250 mm diameter. The machine is equipped with an adjustable lapping arm unit. A cam unit allows the Arm to sweep up & down, ensuring even complete lap over the face. The self-contained adjustable flow compound system is mounted on the side of the machine. The machine...
F-Tool has developed new EcoLine products for sinking EDM, which are designed to meet these requirements. The inexpensive ER-Chuck 50 on FTool ZPS pallets can be used to manufacture up to nine electrodes in the ZPS system in one clamping setup. Electrode manufacturing costs can be reduced drastically by employing multiple clamping setups. The new, inexpensive aluminium ...
This is the biggest gantry miling ever built by Pietro Carnaghi, and with full hydrostatic axis is the optimum machine for heavy components.
- operating pressure: 4...6 bar with air - operating temperature: from 5°C to 60°C - operating principle: wedge and piston design with mechanically restricted guidance - stroke range: from 3 to 7.5 mm - housing materilas: hardened steel - material of functional parts: hardened steel - actation: filtered compressed air - connections: sides - below - pressurization...
Features: ● Double clamp structure promises a high rigidity; ● Excellent for high-feed machining; ● Special insert with three cutting edges increase cost performance; ● Inserts: JDMW1204; JDMW1405. Application: This series face milling cutter is special for high-feed milling.
Table demagnetizers are designed for tool rooms workshops production lines. They realise deep demagnetization of magnetised parts and assemblies, such as bearings, tools, dies, screws etc. The DEM-4 EASY LOGIC line can automatically adapt the height of the magnetic field to the component size, which saves electricity consumption and working costs. The magic of DEM-4 EAS...
Tapping Capacity in steel M2-M14 (M16 all.) KEY FEATURES: - Adjustable speed from 40 to 450 rpm - Working radius r = 1102 mm 360 ° - Electric Brushless Motor 220v - Double-balanced articulated arm system made ​​of special aluminum - Maximum speed extraction tool- Low noise level - Reduced consumption of electricity - Balance and fluidity of moveme...
